Teejet Legacy 6000 Manual Manual de usuario Pagina 118
- Pagina / 159
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Legacy 6000
98-05053 R2
113
Swath Manager LED Brightness
The LED brightness is adjusted by selecting the Adjust LEDs softkey on the De-
vice Manager page with “Swath Manager” selected. Options range from 1 (low)
through 8 (high).
Figure 5-3: Swath Manager LED Brightness
Diagnostic information regarding the system’s CAN switchboxes, Switch Function
Module or Swath Manager 5, and software versions is also available by selecting
the Information softkey. The Update Flashsoftkeycanbeusedtoupdatermware
in the CAN modules. Do not use this function unless directed to do so by your Tee-
Jet Technologies supplier or TeeJet Technologies Customer Service personnel.
Figure 5-4: Module Information
Adjust LEDs
softkey
Information
softkey
Update Flash
softkey (F2)
- TABLE OF CONTENTS 2
- CHAPTER 1 - INTRODUCTION 6
- SYSTEM FEATURES 6
- Chapter 1 - Introduction2 7
- System Components 8
- Switch Function Module 9
- Input Status Module 10
- FieldPilot Module 10
- SWATH MANAGER 5 (SM5) 11
- LEGACY 6000 CONFIGURATIONS 11
- +12v Onl y 12
- Chapter 1 - Introduction8 13
- 45-053 40 14
- 45-081 06 45-081 06 14
- Chapter 1 - Introduction10 15
- CHAPTER 2 - SYSTEM OVERVIEW 16
- INITIAL POWERUP 17
- Chapter 2 - System Overview14 19
- Forward Arrow 19
- PAGE LAYOUT AND NAVIGATION 20
- SYSTEM SETUP 22
- Console Setup 23
- Lightbar Setup 24
- GPS RECEIVER SETUP 25
- Implement Setup 26
- Chapter 2 - System Overview22 27
- CHANNEL SETUP 29
- Channel Favorite 30
- Application Type 31
- Application Type Settings 32
- Drive Type 33
- Chapter 2 - System Overview30 35
- Primary Sensor 37
- Primary Sensor Settings 38
- SECONDARY SENSOR 39
- Settings Description 40
- Monitor Selection 41
- Monitor Settings 42
- Channel Setup Completion 43
- Saving Channel Setup 44
- FIELDPILOT SETUP 45
- FieldPilot Calibration 46
- Adjust Oil Flow 47
- Drive Straight A-B Line 48
- Chapter 2 - System Overview44 49
- Chapter 2 - System Overview46 51
- Bullseye 52
- STARTING JOBS 53
- Manually Naming Jobs 54
- Automatic Job Naming 55
- No PCMCIA Card 55
- ARM LAUNCHER 56
- Calibration Procedure 57
- PRIME INJECTION SYSTEM 58
- )NJECTION 59
- 0RIMING3YSTEM 59
- Prime State Reset Values to 0 60
- JOB REPORT SETUP 62
- Item Description 63
- ARM SETUP 64
- Entering File Names 66
- Swath Manager Lookahead 66
- CAN Switchbox 68
- Input Status Module (ISM) 69
- Swath Manager 5 70
- PRODUCT SETUP 71
- Product Name Selection 72
- Variable Rate Application 73
- Tilt Sensor Functions 76
- Antenna Height 78
- Tilt Sensor Calibration 79
- Next softkey (F6) 80
- CHAPTER 4 - OPERATION 82
- PRODUCT APPLICATION 82
- GPS/BOUNDARY PAGE 83
- Rate Adjustment 84
- Test Speed 85
- Reset Initial Quantity 85
- FieldPilot Adjustments 86
- The Map Page 87
- Product Control 88
- Chapter 4 - Operation84 89
- Solid and Boom Patterns 90
- System Messages 91
- Warning Messages 91
- VEHICLE GUIDANCE 92
- Changing Guidance Patterns 93
- Straight-Line A-B Guidance 93
- Curved A-B Guidance 95
- Headland Guidance 96
- Ignore Headland Guidance 98
- Chapter 4 - Operation94 99
- Headland Off 99
- Ignore Headland 99
- Circle Pivot Guidance 100
- Chapter 4 - Operation96 101
- Mark B softkey 101
- Legacy 6000 102
- 98-05053 R2 102
- FIELDPILOT 103
- LIGHTBAR 104
- Applied Area Detection 105
- MAPPING FIELD BOUNDARIES 106
- MAPPING POINTS AND HAZARDS 107
- Points Mapping 108
- Hazard Mapping 108
- EXITING OPERATION 109
- SHAPE FILES 110
- FIELDWARE MAP MANAGER 111
- LIGHTBAR INDEX 111
- Chapter 4 - Operation108 113
- CHAPTER 5 - SYSTEM TOOLS 114
- DEVICE MANAGER 114
- Backup Files 115
- Restoring System Files 116
- Importing Files 116
- Speedometer 117
- Swath Manager LED Brightness 118
- Channels 119
- GPS Receiver 121
- LightBar 121
- Channels 1,2,3 122
- CARD MANAGER 123
- Chapter 5 - System Tools120 125
- CHAPTER 6 - MAPPER 126
- DATA SETUP 126
- New Job Creation 127
- Existing Job Selection 127
- Naming Jobs Automatically 127
- MAPPER SETUP AND MARKERS 128
- Chapter 6 - Mapper124 129
- Object Name Creation 130
- Object Names Folders 131
- MAPPER APPLICATION 132
- Chapter 6 - Mapper128 133
- Information Page 134
- MAPPER TOOLS 135
- MAPPER OPTIONS 136
- CHAPTER 7 - EXT 138
- GUIDANCE ONLY MODE 138
- LOG DATA MODE 138
- RATE CONTROL MODE 139
- RATE CONTROLLER 140
- Entering Offset Direction Y 141
- Entering Offset Distance Y 142
- CONTROLLER SETUP 143
- Arrow keys 144
- Enter button 144
- PRODUCT SETUP OPERATION 145
- Product Setup Wizard 146
- Select Prescription Map Layer 146
- RATES PAGE 147
- EXITING OPERATIONS 148
- Chapter 7 - EXT144 149
- Using the Calibration Table 155
- APPENDIX C - NH3 APPLICATION 158
Relacionado con productos y manuales para Ordenadores Teejet Legacy 6000 Manual
Ordenadores Teejet LH 500 Manual de usuario
(16 paginas)
(16 paginas)
Ordenadores Teejet LH 500 Manual de usuario
(6 paginas)
(6 paginas)
Ordenadores Teejet LH 1000 Manual de usuario
(16 paginas)
(16 paginas)
Ordenadores Teejet LH 1000 Manual de usuario
(1 paginas)
(1 paginas)
Ordenadores Teejet LH 1200 Manual de usuario
(28 paginas)
(28 paginas)
Ordenadores Teejet LH 1200S Manual de usuario
(28 paginas)
(28 paginas)
Ordenadores Teejet LH 1200S Manual de usuario
(8 paginas)
(8 paginas)
Ordenadores Teejet LH 1600M Manual de usuario
(16 paginas)
(16 paginas)
Ordenadores Teejet LH 1600M Manual de usuario
(8 paginas)
(8 paginas)
Ordenadores Teejet LH 1600 Manual de usuario
(8 paginas)
(8 paginas)
Ordenadores Teejet LH Sprimas Manual de usuario
(12 paginas)
(12 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.163 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales