Teejet Matrix Pro 840G User Manual Manual de usuario Pagina 61
- Pagina / 127
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
54
www.teejet.com
HOMEOVERVIEW SETUP POWER APPENDIXFULL SCREENINTRODUCTION GUIDANCE
Field Level
Field level will calibrate the SCM/TGM’s level surface value.
Before performing Field Level:
• Use a quality GPS receiver/antenna
• Make sure the GPS antenna is mounted as per the
manufacturer’s installation instructions
• The SCM/TGM must be securely mounted to a surface
that moves in parallel to the surface that the GPS antenna is
mounted on. For example, if the antenna is mounted to the
roof of the cab, the SCM/TGM should be mounted to another
surface on the cab, not on the chassis.
• Mount the SCM/TGM on a horizontal surface with the
connectors facing straight up and the arrow on the decal
pointing in the primary direction of travel.
• Choose a calibration site that is as level as possible
To calibrate the SCM/TGM:
1. Position the vehicle on a level surface. Let vehicle sit/settle for at
least 10 seconds.
2. Select Field Level .
3. Let vehicle sit/settle for at least 10 seconds.
4. Press OK .
NOTE: Until vehicle has been stopped for at least 10 seconds, OK
will not be available.
5. Get out of the vehicle to mark on the ground the exact position of
the vehicle (use paint, sticks, or something similar).
6. Turn the vehicle 180 degrees and reposition the vehicle in
exactly the same location (the front wheels should now be where
the back wheels were, and the back wheels should be where the
front wheels were).
7. Let vehicle sit/settle for at least 10 seconds.
8. Press OK .
NOTE: Until vehicle has been stopped for at least 10 seconds, OK
will not be available.
Figure 6-47: Field Level
Cong-> Tilt
Field Level
Enabled
On
Cong-> Tilt
Field Level
Enabled
On
Level Tilt Position One
Note: Antenna Height must be
entered prior to Tilt Calibration.
Position the vehicle on a level surface
and press "OK" to advance to the next
step, or "Cancel" to cancel.
OK
Cancel
Level Tilt Position One
Note: Antenna Height must be
entered prior to Tilt Calibration.
Position the vehicle on a level surface
and press "OK" to advance to the next
step, or "Cancel" to cancel.
OK
Cancel
Level Tilt Position Two
Turn the vehicle 180 degrees and
return to the same location. Press
“OK” to record the level position.
OK
Cancel
Level Tilt Position Two
Turn the vehicle 180 degrees and
return to the same location. Press
“OK” to record the level position.
OK
Cancel
Tilt Calibration Complete
- UsER MANUAL 1
- Table of Contents 2
- CHAPTER 6 SYSTEM SETUP 32 3
- CHAPTER 7 GUIDANCE 78 5
- CHAPTER 1 SYSTEM OVERVIEW 8
- SYSTEM COMPONENTS 9
- Matrix Pro 570G Console 9
- Additional Information 9
- Matrix Pro 840G Console 10
- RealView Camera 10
- Optional Accessories 11
- 98-05238 R1 EN-US 12
- CONFIGURATIONS 13
- 45-10103 15
- DC: xx/xx 15
- Speed Cable 17
- CHAPTER 2 POWER 18
- Setup Screens 20
- Setup Option Information 21
- Drop Down Menu Selections 21
- Dist to Boom (ft) 22
- Conguration 23
- < 0.0 > 24
- Simple Mode 29
- Advanced Mode 29
- SIMPLE MODE 30
- 8.9 < 32
- ADVANCED MODE 33
- 12/14/10 3:52 AM 36
- Continue 36
- CHAPTER 6 SYSTEM SETUP 39
- Ant Height (ft) 41
- Antenna Height (ft) 43
- Guidance Width (ft) 46
- Section 1 Width (in) 46
- Delay On Time (s) 47
- Delay O Time (s) 47
- Valve Setup 49
- Valve Type 49
- Valve Frequency (Hz) 50
- Test Right 51
- Steering Settings 53
- Coarse Steering Adjustment 53
- Fine Steering Adjustment 53
- Deadband 54
- Lookahead 54
- Valve Test 54
- Valve Diagnostics 55
- 1. Select Angle Sensor 57
- Enable/Disable Angle Sensor 58
- Calibrate Sensor 58
- Offset Adjustment 59
- Field Level 61
- LED Spacing (ft) 63
- GPS Status 65
- GGA Requirements 65
- Four Channel VSM 67
- Eight Channel VSM 67
- DATA MANAGEMENT 68
- Manage Data 68
- Manage Data Unavailable 69
- Duplicate Job Data 69
- Transfer 70
- Transfer Unavailable 71
- USB Storage 71
- Internal Storage 72
- Delete Job Data 72
- Reports 73
- Simple Job Mode Options 74
- Advanced Job Mode Options 74
- ESRI Data 75
- PDF Report 75
- KML Data 75
- CONSOLE 77
- Color Scheme 78
- Brightness 78
- Screenshot 78
- Capture a Screenshot 79
- Touch Screen Calibration 79
- Cultural 80
- Time Zone 81
- Calculator 83
- Units Converter 83
- Set Units 84
- Select Value 84
- 0.0 mph 0 ac 85
- Navigation Screens Icons 86
- Status/Information Screens 89
- Assisted/Auto Steering Status 90
- BoomPilot Status 90
- 0.0 mph 0.00 ac 100
- -13 7.2 mph 101
- A+ Nudge Feature 102
- > 0.0 < 103
- Enter Name 104
- Circle Pivot Guidelines 106
- Last Pass Guidelines 108
- Turn Now 109
- 12.7 > 109
- APPLICATION BOUNDARY 110
- Save Delete 111
- RETURN TO POINT 112
- Single Section 114
- ZOOM IN/OUT 114
- Vehicle View 114
- Field View 115
- PAN MODE 116
- REALVIEW SPECIFIC OPTIONS 116
- Single Camera Selection 117
- Split Camera View 118
- RealView Setup Options 118
- Guidance Over Video 119
- Guidance Unavailable 119
- Horizon Line Adjustment 119
- Steering Angle Indicator 120
- APPENDIX A TIME ZONES 121
- Atlantic 122
- Australia 122
- 0.0 ft 123
- Data Management 124
- Console Settings 125
Relacionado con productos y manuales para Ordenadores Teejet Matrix Pro 840G User Manual
(9 paginas)
(9 paginas)
(9 paginas)
(9 paginas)
(9 paginas)
Ordenadores Teejet Matrix 430 Manual de usuario
(12 paginas)
(12 paginas)
Ordenadores Teejet UniPilot Manual de usuario
(20 paginas)
(20 paginas)
Ordenadores Teejet Fieldware Link Manual de usuario
(36 paginas)
(36 paginas)
Ordenadores Teejet RX510 Manual de usuario
(3 paginas)
(3 paginas)
Ordenadores Teejet Fieldware Tool Manual de usuario
(48 paginas)
(48 paginas)
Ordenadores Teejet RMS Office Manual de usuario
(120 paginas)
(120 paginas)
Ordenadores Teejet RX370p Manual de usuario
(24 paginas)
(24 paginas)
Ordenadores Teejet RX375P Receiver Manual de usuario
(16 paginas)
(16 paginas)
Ordenadores Teejet RX 400p Manual de usuario
(151 paginas)
(151 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales