Teejet Matrix Pro 840G User Manual Manual de usuario Pagina 46
- Pagina / 127
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
39
98-05238 R1 EN-US
HOME OVERVIEWSETUP POWERAPPENDIX FULL SCREEN INTRODUCTIONGUIDANCE
#
Number of Boom Sections
Number of Boom Sections establishes the number of available boom
sections. If a SmartCable or Section Driver Module (SDM) is present,
1 to 6 or 1 to 15 section widths can be entered (depending on which
SmartCable or Section Driver Module (SDM) is detected).
1. Press DOWN arrow to access the list of options.
2. Select the number of boom sections on the implement:
Figure 6-13: Number of Boom Sections
Cong->Implement
Num Sections
Spray Width
Guidance Width
75.00 ft
75.00 ft
15
7
8
9
10
11
12
13
14
15
Guidance Width
Guidance Width establishes the width between the guidelines.
Range is 3.28 - 246.1 feet / 1.0 - 75.0 meters.
NOTE: This setting is required for auto steering operation.
1. Press the KEYPAD icon .
2. Use the entry screen to establish the guidance width.
Figure 6-14: Guidance Width
Cong->Implement
Num Sections
Spray Width
Guidance Width
60.00 ft
180.00 ft
15
Guidance Width (ft)
1 2 3
60.00
Clear
4 5 6 <--
7 8 9
0 .
+/-
Spray Width
Spray width establishes the width of each implement section. When
facing forward, boom sections are ordered from left to right along
the boom. Spray width range is 3.28 - 246.1 feet / 1.0 - 75.0 meters.
Boom section width range is 0.0 - 2957.8 inches / 0.0 - 75.0 meters.
NOTE: When entering a boom section width, the total of all sections
must be greater than 3.28 feet (39.3701 inches) / 1.0 meter.
1. Press the KEYPAD icon .
2. Highlight the section to be established.
3. Press the KEYPAD icon .
4. Use the entry screen to establish the spray width.
5. Repeat steps 2 to 4 until all sections have been established.
NOTE: Individual boom sections can be set to different widths.
Figure 6-15: Spray Width
Cong->Implement
Num Sections
Spray Width
Guidance Width
60.00 ft
180.00 ft
15
Config->Implement->Section Widths
Spray Width: 180.00 ft
Section 1 - 144.00 in
Section 2 - 144.00 in
Section 3 - 144.00 in
Section 4 - 144.00 in
Section 5 - 144.00 in
Section 6 - 144.00 in
Section 7 - 144.00 in
Section 1 Width (in)
1 2 3
144.00
Clear
4 5 6 <--
7 8 9
0 .
+/-
- UsER MANUAL 1
- Table of Contents 2
- CHAPTER 6 SYSTEM SETUP 32 3
- CHAPTER 7 GUIDANCE 78 5
- CHAPTER 1 SYSTEM OVERVIEW 8
- SYSTEM COMPONENTS 9
- Matrix Pro 570G Console 9
- Additional Information 9
- Matrix Pro 840G Console 10
- RealView Camera 10
- Optional Accessories 11
- 98-05238 R1 EN-US 12
- CONFIGURATIONS 13
- 45-10103 15
- DC: xx/xx 15
- Speed Cable 17
- CHAPTER 2 POWER 18
- Setup Screens 20
- Setup Option Information 21
- Drop Down Menu Selections 21
- Dist to Boom (ft) 22
- Conguration 23
- < 0.0 > 24
- Simple Mode 29
- Advanced Mode 29
- SIMPLE MODE 30
- 8.9 < 32
- ADVANCED MODE 33
- 12/14/10 3:52 AM 36
- Continue 36
- CHAPTER 6 SYSTEM SETUP 39
- Ant Height (ft) 41
- Antenna Height (ft) 43
- Guidance Width (ft) 46
- Section 1 Width (in) 46
- Delay On Time (s) 47
- Delay O Time (s) 47
- Valve Setup 49
- Valve Type 49
- Valve Frequency (Hz) 50
- Test Right 51
- Steering Settings 53
- Coarse Steering Adjustment 53
- Fine Steering Adjustment 53
- Deadband 54
- Lookahead 54
- Valve Test 54
- Valve Diagnostics 55
- 1. Select Angle Sensor 57
- Enable/Disable Angle Sensor 58
- Calibrate Sensor 58
- Offset Adjustment 59
- Field Level 61
- LED Spacing (ft) 63
- GPS Status 65
- GGA Requirements 65
- Four Channel VSM 67
- Eight Channel VSM 67
- DATA MANAGEMENT 68
- Manage Data 68
- Manage Data Unavailable 69
- Duplicate Job Data 69
- Transfer 70
- Transfer Unavailable 71
- USB Storage 71
- Internal Storage 72
- Delete Job Data 72
- Reports 73
- Simple Job Mode Options 74
- Advanced Job Mode Options 74
- ESRI Data 75
- PDF Report 75
- KML Data 75
- CONSOLE 77
- Color Scheme 78
- Brightness 78
- Screenshot 78
- Capture a Screenshot 79
- Touch Screen Calibration 79
- Cultural 80
- Time Zone 81
- Calculator 83
- Units Converter 83
- Set Units 84
- Select Value 84
- 0.0 mph 0 ac 85
- Navigation Screens Icons 86
- Status/Information Screens 89
- Assisted/Auto Steering Status 90
- BoomPilot Status 90
- 0.0 mph 0.00 ac 100
- -13 7.2 mph 101
- A+ Nudge Feature 102
- > 0.0 < 103
- Enter Name 104
- Circle Pivot Guidelines 106
- Last Pass Guidelines 108
- Turn Now 109
- 12.7 > 109
- APPLICATION BOUNDARY 110
- Save Delete 111
- RETURN TO POINT 112
- Single Section 114
- ZOOM IN/OUT 114
- Vehicle View 114
- Field View 115
- PAN MODE 116
- REALVIEW SPECIFIC OPTIONS 116
- Single Camera Selection 117
- Split Camera View 118
- RealView Setup Options 118
- Guidance Over Video 119
- Guidance Unavailable 119
- Horizon Line Adjustment 119
- Steering Angle Indicator 120
- APPENDIX A TIME ZONES 121
- Atlantic 122
- Australia 122
- 0.0 ft 123
- Data Management 124
- Console Settings 125
Relacionado con productos y manuales para Ordenadores Teejet Matrix Pro 840G User Manual
(9 paginas)
(9 paginas)
(9 paginas)
(9 paginas)
(9 paginas)
Ordenadores Teejet Matrix 430 Manual de usuario
(12 paginas)
(12 paginas)
Ordenadores Teejet UniPilot Manual de usuario
(20 paginas)
(20 paginas)
Ordenadores Teejet Fieldware Link Manual de usuario
(36 paginas)
(36 paginas)
Ordenadores Teejet RX510 Manual de usuario
(3 paginas)
(3 paginas)
Ordenadores Teejet Fieldware Tool Manual de usuario
(48 paginas)
(48 paginas)
Ordenadores Teejet RMS Office Manual de usuario
(120 paginas)
(120 paginas)
Ordenadores Teejet RX370p Manual de usuario
(24 paginas)
(24 paginas)
Ordenadores Teejet RX375P Receiver Manual de usuario
(16 paginas)
(16 paginas)
Ordenadores Teejet RX 400p Manual de usuario
(151 paginas)
(151 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.914 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales