Teejet Matrix Pro 840G User Manual Manual de usuario Pagina 54
- Pagina / 127
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
47
98-05238 R1 EN-US
HOME OVERVIEWSETUP POWERAPPENDIX FULL SCREEN INTRODUCTIONGUIDANCE
Deadband
Deadband adjusts if steering is too choppy/responsive or remains
consistently off the guideline. As the value is increased, stability will
increase but so will steady state error. Range is 1 - 10. Default is 1.
1. Press:
►UP arrow if steering is too choppy or too responsive.
►DOWN arrow if the vehicle remains consistently off the
guideline.
Figure 6-35: Deadband
Cong-> AutoSteer->Steering Setting
Coarse Adjustment
Fine Adjustment
Deadband
Lookahead
125.0
4.0 s25.0
Lookahead
Lookahead used during Straight AB Guidance mode to
adjust the vehicle’s approach to the guideline. Fine tune the
Lookahead by conducting several approaches to the guideline.
Range is 0.0 - 10.0 seconds. Default is 4.0 seconds.
1. Press:
►UP arrow if the vehicle is overshooting the guideline when
approaching.
►DOWN arrow if the vehicle takes too long to get to the
guideline.
Figure 6-36: Lookahead
Cong-> AutoSteer->Steering Setting
Coarse Adjustment
Fine Adjustment
Deadband
Lookahead
125.0
4.0 s25.0
Valve Test
The Valve Test veries if steering is directed correctly. It can also be
used to test the amount of time to steer the wheels from full left to full
right (lock to lock) for non-proportional valves.
For non-proportional valves, the amount of time for left-to-right
or right-to-left (lock to lock) will be established by mechanically
adjusting oil ow through the valve.
For a UniPilot ESM, the amount of time for left-to-right or right-to-left
(lock to lock) will be established by adjusting the Max Duty Cycle
value.
NOTE: See section “Verify Operation of Hydraulics and Set the
Steering Control Rate” of your specific FieldPilot Installation
Manual for your specific lock to lock time.
1. Select Valve Test .
2. While the vehicle is moving in a slow forward motion,
turn the wheels all the way to the left.
3. Press RIGHT arrow .
4. Press the engage/disengage switch or foot switch to activate the
test. This will start a timer as well as turn the vehicle to the right.
WARNING! When using a UniPilot, the UniPilot will move the
steering wheel very quickly. Keep loose clothing, hair and
hands away from the steering wheel while preforming this
test.
5. Press the engage/disengage switch or foot switch when the
wheels are all the way to the right. The time displayed is the lock
to lock time.
- UsER MANUAL 1
- Table of Contents 2
- CHAPTER 6 SYSTEM SETUP 32 3
- CHAPTER 7 GUIDANCE 78 5
- CHAPTER 1 SYSTEM OVERVIEW 8
- SYSTEM COMPONENTS 9
- Matrix Pro 570G Console 9
- Additional Information 9
- Matrix Pro 840G Console 10
- RealView Camera 10
- Optional Accessories 11
- 98-05238 R1 EN-US 12
- CONFIGURATIONS 13
- 45-10103 15
- DC: xx/xx 15
- Speed Cable 17
- CHAPTER 2 POWER 18
- Setup Screens 20
- Setup Option Information 21
- Drop Down Menu Selections 21
- Dist to Boom (ft) 22
- Conguration 23
- < 0.0 > 24
- Simple Mode 29
- Advanced Mode 29
- SIMPLE MODE 30
- 8.9 < 32
- ADVANCED MODE 33
- 12/14/10 3:52 AM 36
- Continue 36
- CHAPTER 6 SYSTEM SETUP 39
- Ant Height (ft) 41
- Antenna Height (ft) 43
- Guidance Width (ft) 46
- Section 1 Width (in) 46
- Delay On Time (s) 47
- Delay O Time (s) 47
- Valve Setup 49
- Valve Type 49
- Valve Frequency (Hz) 50
- Test Right 51
- Steering Settings 53
- Coarse Steering Adjustment 53
- Fine Steering Adjustment 53
- Deadband 54
- Lookahead 54
- Valve Test 54
- Valve Diagnostics 55
- 1. Select Angle Sensor 57
- Enable/Disable Angle Sensor 58
- Calibrate Sensor 58
- Offset Adjustment 59
- Field Level 61
- LED Spacing (ft) 63
- GPS Status 65
- GGA Requirements 65
- Four Channel VSM 67
- Eight Channel VSM 67
- DATA MANAGEMENT 68
- Manage Data 68
- Manage Data Unavailable 69
- Duplicate Job Data 69
- Transfer 70
- Transfer Unavailable 71
- USB Storage 71
- Internal Storage 72
- Delete Job Data 72
- Reports 73
- Simple Job Mode Options 74
- Advanced Job Mode Options 74
- ESRI Data 75
- PDF Report 75
- KML Data 75
- CONSOLE 77
- Color Scheme 78
- Brightness 78
- Screenshot 78
- Capture a Screenshot 79
- Touch Screen Calibration 79
- Cultural 80
- Time Zone 81
- Calculator 83
- Units Converter 83
- Set Units 84
- Select Value 84
- 0.0 mph 0 ac 85
- Navigation Screens Icons 86
- Status/Information Screens 89
- Assisted/Auto Steering Status 90
- BoomPilot Status 90
- 0.0 mph 0.00 ac 100
- -13 7.2 mph 101
- A+ Nudge Feature 102
- > 0.0 < 103
- Enter Name 104
- Circle Pivot Guidelines 106
- Last Pass Guidelines 108
- Turn Now 109
- 12.7 > 109
- APPLICATION BOUNDARY 110
- Save Delete 111
- RETURN TO POINT 112
- Single Section 114
- ZOOM IN/OUT 114
- Vehicle View 114
- Field View 115
- PAN MODE 116
- REALVIEW SPECIFIC OPTIONS 116
- Single Camera Selection 117
- Split Camera View 118
- RealView Setup Options 118
- Guidance Over Video 119
- Guidance Unavailable 119
- Horizon Line Adjustment 119
- Steering Angle Indicator 120
- APPENDIX A TIME ZONES 121
- Atlantic 122
- Australia 122
- 0.0 ft 123
- Data Management 124
- Console Settings 125
Relacionado con productos y manuales para Ordenadores Teejet Matrix Pro 840G User Manual
(9 paginas)
(9 paginas)
(9 paginas)
(9 paginas)
(9 paginas)
Ordenadores Teejet Matrix 430 Manual de usuario
(12 paginas)
(12 paginas)
Ordenadores Teejet UniPilot Manual de usuario
(20 paginas)
(20 paginas)
Ordenadores Teejet Fieldware Link Manual de usuario
(36 paginas)
(36 paginas)
Ordenadores Teejet RX510 Manual de usuario
(3 paginas)
(3 paginas)
Ordenadores Teejet Fieldware Tool Manual de usuario
(48 paginas)
(48 paginas)
Ordenadores Teejet RMS Office Manual de usuario
(120 paginas)
(120 paginas)
Ordenadores Teejet RX370p Manual de usuario
(24 paginas)
(24 paginas)
Ordenadores Teejet RX375P Receiver Manual de usuario
(16 paginas)
(16 paginas)
Ordenadores Teejet RX 400p Manual de usuario
(151 paginas)
(151 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales