Teejet Matrix Pro 840G User Manual Manual de usuario Pagina 110
- Pagina / 127
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
103
98-05238 R1 EN-US
HOME OVERVIEWSETUP POWERAPPENDIX FULL SCREEN INTRODUCTIONGUIDANCE
APPLICATION BOUNDARY
Application boundaries establish areas where application is and
is not applied while using ABSC or BoomPilot. Boundaries can be
established in all guidance modes. One exterior boundary and up to
ve (5) interior boundaries can be stored at one time.
Using Data->Manage Data or with Fieldware Link, a user can
duplicate and edit jobs for reuse of boundaries and guidelines for
different applications over the same eld.
To establish an exterior application boundary:
1. Drive to a desired location at the perimeter of the field/
application area.
2. Press NAVIGATION AND GUIDANCE OPTIONS icon to
display navigation options.
3. While the vehicle is in motion, press BOUNDARY icon .
4. Travel the perimeter of the eld/area.
5. Finish boundary:
►Travel to within one swath width of the starting point. The
boundary will close automatically (the white guideline will turn
black)
►Press BOUNDARY FINISH icon . A straight line will
complete the boundary between your current location and the
starting point
6. Press:
►Save – to save the boundary
►Delete – to delete the boundary
NOTE: On the external or initial boundary, the BOUNDARY FINISH
icon is not available for selection (grayed out) until the
minimum distance is travelled (five-times the swath width).
If mapping a boundary with one or more booms folded in and
turned off, it is necessary to maintain this boom conguration for the
duration of the boundary pass. Any changes made to the number of
booms turned on, and therefore the width of the machine after the
boundary mapping process has started, will result in the application
mapping the boundary at the outer edge of all the programmed
booms – not necessarily those turned on at any given point in time
during the boundary pass .
When mapping a boundary with some booms turned off, it is
necessary to turn BoomPilot to Manual mode and turn ON the
Master and Boom switches for all booms that will be used during
the Boundary pass. Once the boundary pass is complete the Boom
switches can be turned OFF, Master switch remains ON, BoomPilot
can be returned to Automatic mode and automatic boom section
control can then be used.
Note: If a boundary is mapped with some booms folded
as described above, it may be necessary to use the
A+ NUDGE icon
A
on the guideline over to the correct
position for subsequent passes in the field.
Figure 7-52: Boundary in Progress
0.00 ac 0.0 mph
2.32 ac 7.2 mph
Mark A
Figure 7-53: Finish Boundary – Straight line to starting point
2.32 ac 7.2 mph
Mark A
Figure 7-54: Finish Boundary – Travel to starting point
4.68 ac 7.2 mph
Mark A
- UsER MANUAL 1
- Table of Contents 2
- CHAPTER 6 SYSTEM SETUP 32 3
- CHAPTER 7 GUIDANCE 78 5
- CHAPTER 1 SYSTEM OVERVIEW 8
- SYSTEM COMPONENTS 9
- Matrix Pro 570G Console 9
- Additional Information 9
- Matrix Pro 840G Console 10
- RealView Camera 10
- Optional Accessories 11
- 98-05238 R1 EN-US 12
- CONFIGURATIONS 13
- 45-10103 15
- DC: xx/xx 15
- Speed Cable 17
- CHAPTER 2 POWER 18
- Setup Screens 20
- Setup Option Information 21
- Drop Down Menu Selections 21
- Dist to Boom (ft) 22
- Conguration 23
- < 0.0 > 24
- Simple Mode 29
- Advanced Mode 29
- SIMPLE MODE 30
- 8.9 < 32
- ADVANCED MODE 33
- 12/14/10 3:52 AM 36
- Continue 36
- CHAPTER 6 SYSTEM SETUP 39
- Ant Height (ft) 41
- Antenna Height (ft) 43
- Guidance Width (ft) 46
- Section 1 Width (in) 46
- Delay On Time (s) 47
- Delay O Time (s) 47
- Valve Setup 49
- Valve Type 49
- Valve Frequency (Hz) 50
- Test Right 51
- Steering Settings 53
- Coarse Steering Adjustment 53
- Fine Steering Adjustment 53
- Deadband 54
- Lookahead 54
- Valve Test 54
- Valve Diagnostics 55
- 1. Select Angle Sensor 57
- Enable/Disable Angle Sensor 58
- Calibrate Sensor 58
- Offset Adjustment 59
- Field Level 61
- LED Spacing (ft) 63
- GPS Status 65
- GGA Requirements 65
- Four Channel VSM 67
- Eight Channel VSM 67
- DATA MANAGEMENT 68
- Manage Data 68
- Manage Data Unavailable 69
- Duplicate Job Data 69
- Transfer 70
- Transfer Unavailable 71
- USB Storage 71
- Internal Storage 72
- Delete Job Data 72
- Reports 73
- Simple Job Mode Options 74
- Advanced Job Mode Options 74
- ESRI Data 75
- PDF Report 75
- KML Data 75
- CONSOLE 77
- Color Scheme 78
- Brightness 78
- Screenshot 78
- Capture a Screenshot 79
- Touch Screen Calibration 79
- Cultural 80
- Time Zone 81
- Calculator 83
- Units Converter 83
- Set Units 84
- Select Value 84
- 0.0 mph 0 ac 85
- Navigation Screens Icons 86
- Status/Information Screens 89
- Assisted/Auto Steering Status 90
- BoomPilot Status 90
- 0.0 mph 0.00 ac 100
- -13 7.2 mph 101
- A+ Nudge Feature 102
- > 0.0 < 103
- Enter Name 104
- Circle Pivot Guidelines 106
- Last Pass Guidelines 108
- Turn Now 109
- 12.7 > 109
- APPLICATION BOUNDARY 110
- Save Delete 111
- RETURN TO POINT 112
- Single Section 114
- ZOOM IN/OUT 114
- Vehicle View 114
- Field View 115
- PAN MODE 116
- REALVIEW SPECIFIC OPTIONS 116
- Single Camera Selection 117
- Split Camera View 118
- RealView Setup Options 118
- Guidance Over Video 119
- Guidance Unavailable 119
- Horizon Line Adjustment 119
- Steering Angle Indicator 120
- APPENDIX A TIME ZONES 121
- Atlantic 122
- Australia 122
- 0.0 ft 123
- Data Management 124
- Console Settings 125
Relacionado con productos y manuales para Ordenadores Teejet Matrix Pro 840G User Manual
(9 paginas)
(9 paginas)
(9 paginas)
(9 paginas)
(9 paginas)
Ordenadores Teejet Matrix 430 Manual de usuario
(12 paginas)
(12 paginas)
Ordenadores Teejet UniPilot Manual de usuario
(20 paginas)
(20 paginas)
Ordenadores Teejet Fieldware Link Manual de usuario
(36 paginas)
(36 paginas)
Ordenadores Teejet RX510 Manual de usuario
(3 paginas)
(3 paginas)
Ordenadores Teejet Fieldware Tool Manual de usuario
(48 paginas)
(48 paginas)
Ordenadores Teejet RMS Office Manual de usuario
(120 paginas)
(120 paginas)
Ordenadores Teejet RX370p Manual de usuario
(24 paginas)
(24 paginas)
Ordenadores Teejet RX375P Receiver Manual de usuario
(16 paginas)
(16 paginas)
Ordenadores Teejet RX 400p Manual de usuario
(151 paginas)
(151 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales