Teejet Matrix 840G User Manual Manual de usuario Pagina 43
- Pagina / 67
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
●
38
Vehicle View
To access the Vehicle View screen.
1. Press HOME BUTTON or press the screen to activate the
icons and select HOME ICON in bottom left corner of screen.
2. Select VEHICLE VIEW from Home Menu .
Figure 3-12: Home Menu
Swath ha
0.00
0.0
Guidance Mode Select
Guidance Modes include Straight A-B , Curved A-B ,
Circle Pivot , Last Pass , and No Guidance Mode .
Guidance with SmartCable or SDM
• Turn the controller master switch to the “On” position. The
individual boom section switches should remain in the “Off”
position.
• Activate BoomPilot. See BoomPilot section for details.
• In areas where application is not desired, manually turn “off”
the rate controller master switch to shut off the booms. Turn the
master switch “on” to resume application.
NOTE: This does not apply unless a SmartCable or SDM is installed
on the system.
Straight A-B Guidance
Straight A-B guidance provides straight line guidance based on A and
B reference points. The original A and B points are used to calculate
all other parallel guidelines.
Activate Straight A-B Guidance
1. Press the screen to activate the icons and select the GUIDANCE
MODE ICON .
2. Select STRAIGHT A-B GUIDANCE .
◄Status Bar Icon will change to .
Figure 3-13: Guidance Mode Selection
Swath ha
0.00
0.0
Marking A and B Points
1. Drive to the desired location of Point A .
2. While the vehicle is in motion, press MARK A ICON
A
.
3. Drive to the desired location of Point B .
4. Press the MARK B ICON
B
to establish the A-B line.
NOTE: The MARK B ICON
B
is not available for selection (greyed
out) until the minimum distance is travelled (3.0 m).
Use CANCEL MARK ICON to cancel the Mark A command and
revert to the previous A-B guideline (when established).
Figure 3-14: Mark A and B Points
km/h ha
1.2010.5
Mark A
km/h ha
2.6010.5
Mark B
The console will begin providing navigation information.
Figure 3-15: Straight A-B Guidance
Swath ha
3.570
0.0
NOTE: A compass is displayed during perspective view (the ZOOM
IN BUTTON or ZOOM IN ICON is used to display the
horizon).
A+ Nudge Feature
The A+ Nudge feature allows the existing A-B guideline to be shifted
to the vehicle’s current location.
1. Press A+ NUDGE ICON
A
to establish the new guideline.
Figure 3-16: A+ Nudge
Swath ha
3.80-2
5.1
Swath ha
3.81-2
0.0
- U s E R M A N U A L 1
- Table of Contents 2
- CHAPTER 1– PRODUCT OVERVIEW 6
- SYSTEM FEATURES 6
- SYSTEM COMPONENTS 6
- Matrix 570G Console 6
- RealView Camera 7
- Matrix 840G Console 7
- Video Selector Modules 8
- GPS Antennas 8
- Configurations 10
- Engage/Disengage 11
- Power on/off 12
- Start Up Sequence 13
- GENERAL OPERATION INFORMATION 13
- 98-05188 R2www.teejet.com 14
- Page Layout and Navigation 15
- Home Menu 16
- CHAPTER 2 – UNIT SETUP 16
- SYSTEM SETUP 17
- Lightbar 17
- Display Mode 18
- LED Brightness 18
- Language 19
- Time Zone 20
- GPS Type 20
- GPS Port 21
- GPS Status 21
- GGA Requirements 22
- TSLIB calibration utility 23
- Touch crosshair to calibrate 23
- Screenshot 24
- Enable/Disable 24
- Capture an Image 25
- About/Save 25
- Save About Information 25
- Eight Channel VSM 26
- BOOMPILOT/SINGLE BOOM SETUP 27
- BoomPilot Setup 27
- Delay On 28
- Delay Off 29
- Number of Boom Sections 29
- Boom Section Width 29
- Single Boom Setup 30
- VEHICLE SETUP 30
- Vehicle Type 31
- Antenna Height 31
- Direction to Boom 31
- TILT GYRO MODULE SETUP 32
- Level Tilt Position 1 33
- Level Tilt Position 2 33
- Tilt Calibration Complete 33
- Tilt Correction Off 33
- FIELDPILOT SETUP 34
- Autosteer 34
- Valve Setup 35
- Cycle Left 36
- Cycle Right 36
- Maximum Duty Cycle 36
- Valve Test 37
- Con gure FieldPilot 37
- Coarse Steering Adjustment 38
- Fine Steering Adjustment 38
- Deadband 39
- Lookahead 39
- CHAPTER 3 – GUIDANCE 40
- GUIDANCE OPERATION MODES 40
- Straight A-B Guidance 40
- Curved A-B Guidance 40
- Circle Pivot Guidance 40
- Last Pass Guidance 41
- GUIDANCE BAR & STATUS BAR 41
- Guidance Bar 41
- Status Bar 41
- 0.5314.6 42
- Vehicle View 43
- Guidance Mode Select 43
- Marking A and B Points 45
- Activate Last Pass Guidance 45
- Last Pass 45
- Create Field Boundary 45
- Zoom In/Out & Perspective 47
- BoomPilot 47
- Return to Point 49
- Zoom In/Out 50
- World View 50
- Pan Mode 50
- Guidance Over Video 52
- Steering Angle Indicator 53
- Single Camera Selection 53
- Four Channel VSM 54
- Split Camera View 55
- Guideline Adjustment 56
- CHAPTER 4 – MONITORING 57
- JOB VIEW 57
- Job Information 57
- Save Information 57
- PDF Report 58
- KML Data 58
- BOOM MONITORING 59
- Boom Monitor 59
- Menu Options 61
- Unit Setup 61
- CHAPTER 5 – APPENDIX 61
- APPENDIX A ICON REFERENCE 61
- BoomPilot/Single Boom Setup 62
- Vehicle Setup 62
- Tilt Gyro Module Setup 62
- FieldPilot Setup 62
- Commandes générales 62
- Guidance Screens 63
- Job View 64
- APPENDIX B TIME ZONES 64
Relacionado con productos y manuales para Ordenadores Teejet Matrix 840G User Manual
(58 paginas)
(2 paginas)
(2 paginas)
(2 paginas)
(2 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales