Teejet Matrix 840G User Manual Manual de usuario Pagina 23
- Pagina / 67
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
●
18
LCD Brightness
LCD Brightness adjusts the brightness of the console display.
Range is 0 - 100.
1. Press CONSOLE ICON
.
2. Press LCD BRIGHTNESS ICON .
3. Press the PLUS/MINUS ICONS to adjust LED brightness.
◄Higher the number, the brighter the LCD.
◄Lower the number, the dimmer the LCD.
4. Press
►PAGE RIGHT ARROW to proceed to Touch Screen
Calibration.
►SYSTEM SETUP TAB to return to main System Setup
screen.
NOTE: Press & hold PLUS/MINUS ICONS to quickly adjust
settings.
WARNING!: In hot conditions, settings above 50 may cause a High
Temperature Warning. The console will automatically dim the
screen to reduce the console temperature.
Figure 2-21: LCD Brightness
Touch Screen Calibration with Software Version
1.00 to 1.02
Touch Screen Calibration is used to force a touch screen calibration
the next time a power cycle occurs.
1. Press CONSOLE ICON .
2. Press CALIBRATE TOUCH SCREEN ICON .
3. Press HAND ICON to enable the touch screen calibration
process.
4. “Force touch screen calibration next time unit starts up?”
Press
►Yes – to return to the Touch Screen Calibration screen. The
calibration will be performed when power to the console is
cycled.
►No – to return to the Touch Screen Calibration screen
5. Press
►PAGE RIGHT ARROW to proceed to Screenshot.
►SYSTEM SETUP TAB to return to main System Setup
screen.
Figure 2-22: Touch Screen Calibration
Figure 2-23: Touch Screen Calibration
Next Power Cycle
The calibration screen will be displayed before the console boots.
1. “TSLIB calibration utility Touch crosshair to calibrate”
Press series of 5 crosshairs .
2. Console will resume booting.
After the fi fth (5th) crosshair is pressed, the calibration process takes
approximately 30 - 45 seconds to complete.
Figure 2-24: Touch Screen Calibration Process
TSLIB calibration utility
Touch crosshair to calibrate
- U s E R M A N U A L 1
- Table of Contents 2
- CHAPTER 1– PRODUCT OVERVIEW 6
- SYSTEM FEATURES 6
- SYSTEM COMPONENTS 6
- Matrix 570G Console 6
- RealView Camera 7
- Matrix 840G Console 7
- Video Selector Modules 8
- GPS Antennas 8
- Configurations 10
- Engage/Disengage 11
- Power on/off 12
- Start Up Sequence 13
- GENERAL OPERATION INFORMATION 13
- 98-05188 R2www.teejet.com 14
- Page Layout and Navigation 15
- Home Menu 16
- CHAPTER 2 – UNIT SETUP 16
- SYSTEM SETUP 17
- Lightbar 17
- Display Mode 18
- LED Brightness 18
- Language 19
- Time Zone 20
- GPS Type 20
- GPS Port 21
- GPS Status 21
- GGA Requirements 22
- TSLIB calibration utility 23
- Touch crosshair to calibrate 23
- Screenshot 24
- Enable/Disable 24
- Capture an Image 25
- About/Save 25
- Save About Information 25
- Eight Channel VSM 26
- BOOMPILOT/SINGLE BOOM SETUP 27
- BoomPilot Setup 27
- Delay On 28
- Delay Off 29
- Number of Boom Sections 29
- Boom Section Width 29
- Single Boom Setup 30
- VEHICLE SETUP 30
- Vehicle Type 31
- Antenna Height 31
- Direction to Boom 31
- TILT GYRO MODULE SETUP 32
- Level Tilt Position 1 33
- Level Tilt Position 2 33
- Tilt Calibration Complete 33
- Tilt Correction Off 33
- FIELDPILOT SETUP 34
- Autosteer 34
- Valve Setup 35
- Cycle Left 36
- Cycle Right 36
- Maximum Duty Cycle 36
- Valve Test 37
- Con gure FieldPilot 37
- Coarse Steering Adjustment 38
- Fine Steering Adjustment 38
- Deadband 39
- Lookahead 39
- CHAPTER 3 – GUIDANCE 40
- GUIDANCE OPERATION MODES 40
- Straight A-B Guidance 40
- Curved A-B Guidance 40
- Circle Pivot Guidance 40
- Last Pass Guidance 41
- GUIDANCE BAR & STATUS BAR 41
- Guidance Bar 41
- Status Bar 41
- 0.5314.6 42
- Vehicle View 43
- Guidance Mode Select 43
- Marking A and B Points 45
- Activate Last Pass Guidance 45
- Last Pass 45
- Create Field Boundary 45
- Zoom In/Out & Perspective 47
- BoomPilot 47
- Return to Point 49
- Zoom In/Out 50
- World View 50
- Pan Mode 50
- Guidance Over Video 52
- Steering Angle Indicator 53
- Single Camera Selection 53
- Four Channel VSM 54
- Split Camera View 55
- Guideline Adjustment 56
- CHAPTER 4 – MONITORING 57
- JOB VIEW 57
- Job Information 57
- Save Information 57
- PDF Report 58
- KML Data 58
- BOOM MONITORING 59
- Boom Monitor 59
- Menu Options 61
- Unit Setup 61
- CHAPTER 5 – APPENDIX 61
- APPENDIX A ICON REFERENCE 61
- BoomPilot/Single Boom Setup 62
- Vehicle Setup 62
- Tilt Gyro Module Setup 62
- FieldPilot Setup 62
- Commandes générales 62
- Guidance Screens 63
- Job View 64
- APPENDIX B TIME ZONES 64
Relacionado con productos y manuales para Ordenadores Teejet Matrix 840G User Manual
(58 paginas)
(2 paginas)
(2 paginas)
(2 paginas)
(2 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales