Teejet Legacy 6000 CAN Guide Manual de usuario Pagina 193
- Pagina / 194
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Fieldware for The Legacy 6000
Software Version 2.11
C-1
Appendix C - NH3 Application
Appendix C - NH3 Application
When using the NH3 mode review the settings below to ensure the Cal # and Density have been
entered correctly. The Cal # is located in PCM setup under Primary Sensor Tools. The Density
value is accessed from the ARM launcher page in Product Setup.
NH3 Application Cal#
For All NH3 applications the Cal # units should be entered in Pulses / Gallon. The Cal # units DO
NOT change even if the displayed units are in (lbs. of NH3 / acre) or (lbs. Actual N / acre).
Density for NH3 and Actual N
Density will determine the units of the applied and displayed rate (lbs of NH3 / acre or lbs of actual
N / acre) in real-time applications. If the operator wants to apply and display the rate in lbs of NH3
/ acre, the operator would enter a density of lbs of NH3 / gal. If the operator wants to apply and dis-
play the rate in lbs of Actual N / acre, the operator would enter a density of lbs of Actual N / gal.
NOTE: Temperature affects the Density. Use the chart below to locate the correct value (Figure
1-1). Use the temperature or tank pressure column to determine the correct density.
Example:
Cal # - pulses / gal
Operator wants to enter and display pounds of actual N / acre. If the temperature is 65
o
F, density
would be entered in Product Setup as 4.19 lbs of actual N / per gal.
NH3 is 82% Actual N by weight
1gal NH3 @ 60
o
F = 5.15lbs x .82 = 4.22lbs of Actual N / 1 gal of NH3
Figure 1-1: Density Table
°F °C PSI bar NH3 lbs/gal NH3 Kg/L N lbs/gal N Kg/L
0 -18 15.7 1.1 5.53 0.66 4.54 0.54
10 -12 23.8 1.6 5.47 0.66 4.49 0.54
20 -7 33.5 2.3 5.41 0.65 4.44 0.53
30 -1 45 3.1 5.34 0.64 4.37 0.53
40 4 58.6 4 5.28 0.63 4.33 0.52
50 10 74.5 5.1 5.21 0.63 4.27 0.52
60 16 92.9 6.1 5.15 0.62 4.22 0.51
65 18 103.1 7.1 5.11 0.61 4.19 0.5
70 21 114.1 7.9 5.08 0.61 4.17 0.5
75 24 125.8 8.7 5.04 0.6 4.13 0.49
80 27 138.3 9.5 5.01 0.6 4.11 0.49
85 29 151.7 10.5 4.97 0.6 4.08 0.49
90 32 165.9 11.4 4.94 0.59 4.05 0.48
95 35 181.1 12.5 4.9 0.59 4.02 0.48
100 38 197.2 13.6 4.87 0.58 3.99 0.47
Properties Of Liquid Ammonia At Various Temperatures
Temperature Pressure Liquid Densit
y
(
lbs /
g
al of NH3
)
- USER GUIDE 1
- Copyrights 2
- Trademarks 2
- Limitation of Liability 2
- Table of Contents 3
- Fieldware for The Legacy 6000 10
- System Introduction 12
- CAN Bus Versatility and Value 13
- The Legacy 6000 Console 15
- Power Speed Module 16
- Switch Sense Module 17
- Switch Function Module 18
- Product Control Module 19
- Swath XL Lightbar 20
- CAN Bus Cable Specifications 21
- CAN Modules (PCM, SSM, PSM) 21
- Cable Harnesses 22
- PCM Cable Options 23
- Table 1-1: PCM Cable Options 23
- Chapter 2 - Getting Started 31
- Software Overview 32
- Standard Pages 34
- Setup Menu Page 35
- Setup Wizard 35
- Setup Sub-Groups 35
- Exiting a Setup Menu Page 35
- Data Entry Page 36
- System Setup 37
- Console Setup 38
- Lightbar Setup 39
- GPS Receiver Setup 40
- Implement Setup 41
- Entering the Implement Width 42
- Number of Swaths Page 43
- Entering the Section Width 44
- The Offset Distance Y 45
- Setting the PCM Assignment 47
- Completing Implement Setup 48
- PCM Serial Number 49
- PCM Number 49
- PCM Name 49
- Favorites Description 51
- Setting the Application Type 52
- Application 53
- Settings 53
- Setting the Drive Type 54
- Servo Settings Description 55
- PWM Settings Description 55
- Setting the Units 57
- Selecting the Primary Sensor 58
- Sensor Settings Definition 59
- Selecting a Monitor 64
- Monitor Settings Description 65
- Finishing the PCM Setup 67
- Chapter 3 - Real-time Setup 71
- Operation Overview 72
- Step Description 73
- Figure 3-3: The Job Name Page 75
- No PCMCIA Card Setup 76
- ARM Launcher 77
- Performing a Calibration 78
- Distance/Speed Calibration 79
- Pressure Calibration 89
- NH3 In-Field Calibration 91
- Injection Static Calibration 93
- Prime Injection System 95
- 2. Setup System for Priming 96
- 3. Start Prime 96
- 2. Start Reverse Prime 98
- Job Report Setup 99
- Item Description 100
- ARM Setup 101
- Setup Item Description 102
- Software Version 2.11 103
- Folder Button 104
- Product Setup 105
- The Select PCM Page 107
- Select the Product Name 108
- Variable Rate Application 109
- Multiproduct Variable Rate 110
- Chapter Notes 113
- Fieldware for the Legacy 6000 114
- Product Application 116
- Information Pages 117
- Manual Control 118
- Test Speed 119
- Reset Initial Quantity 119
- Soft-key Description 120
- The Map Page 121
- System Message 125
- Warning Message 125
- Error Message 126
- Real-time Guidance Operation 127
- Mark Point A 128
- Mark Point B 128
- The Headland Guidance Pattern 129
- Headland Pattern Example 130
- Step 4: Ignore Headland Data 135
- The Circle Pivot Pattern 137
- Circle Pivot Example 138
- Marking Point A 138
- Marking Point B 138
- Applied Area Detection 142
- Mapping a Field Boundary 144
- Mapping Points and Hazards 146
- Marking a Hazard 147
- Object Name File 147
- Exiting Real-Time Operation 148
- Lightbar Index 149
- Lightbar State Description 150
- Chapter 5 - System Tools 155
- System Tools 156
- Device Manager 157
- Figure 5-4: 158
- Button Description 158
- Figure 5-6: 160
- Required Items: 161
- Card Manager 163
- 5-12 Chapter 5 - System Tools 166
- 5Chapter Notes 166
- Chapter 6 - Running Mapper 167
- Mapper Introduction 168
- Starting a Job 169
- Figure 6-3: The Job Name Page 170
- Soft-key Step Description 171
- Table 6-1: Mapper Setup 171
- Figure 6-4: Mapper Setup 172
- Mapper Setup 172
- Description 172
- Parameter Description 173
- Enter Road Marker Name 174
- Creating Object Name 175
- Real-time pages 176
- Mapper Tools 180
- Object Description 181
- Figure 6-13: The Options Menu 182
- Option Description 182
- LIQFLOW-A GRANSERVO-A 185
- GRANSERVO-B GRANPWM-A 186
- GRANDC-A SPINMOTOR-A 187
- Using the Calibration Table 191
- Appendix C - NH3 Application 193
Relacionado con productos y manuales para Ordenadores Teejet Legacy 6000 CAN Guide
Ordenadores Teejet LH 500 Manual de usuario
(16 paginas)
(16 paginas)
Ordenadores Teejet LH 500 Manual de usuario
(6 paginas)
(6 paginas)
Ordenadores Teejet LH 1000 Manual de usuario
(16 paginas)
(16 paginas)
Ordenadores Teejet LH 1000 Manual de usuario
(1 paginas)
(1 paginas)
Ordenadores Teejet LH 1200 Manual de usuario
(28 paginas)
(28 paginas)
Ordenadores Teejet LH 1200S Manual de usuario
(28 paginas)
(28 paginas)
Ordenadores Teejet LH 1200S Manual de usuario
(8 paginas)
(8 paginas)
Ordenadores Teejet LH 1600M Manual de usuario
(16 paginas)
(16 paginas)
Ordenadores Teejet LH 1600M Manual de usuario
(8 paginas)
(8 paginas)
Ordenadores Teejet LH 1600 Manual de usuario
(8 paginas)
(8 paginas)
Ordenadores Teejet LH Sprimas Manual de usuario
(12 paginas)
(12 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.822 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales