Teejet Fieldware SA 2.0 for Legacy 6000 Manual de usuario Pagina 148
- Pagina / 172
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5-10 Chapter 5 - Fieldware FieldPilot
Fieldware-SA Real-Time Operation
Fieldware-SA for the Legacy 6000
Software Version 2.00
Fieldware-SA Real-Time Operation
When the setup process is completed, real-time operation of FieldPilot and Fieldware can begin.
To start real-time setup and operation, press the Bull’s Eye button located on the Fieldware
Launcher page (Figure 5-8).
Real-time Setup
It is recommended that vehicle trajectory data be collected and stored to the PC card. Job reports
can be created in Mid-Tech’s Map Manager desktop software. Storing data also allows the AB
guideline file to be saved and used again at a later date. To collect data, make sure the PC Card
setting is set to Yes. This setting is located in Console setup (see “Console Setup” on page 2-13).
If data is being collected and stored, a new Job name must be entered or an existing job name
selected. This step takes place when the Main Launcher Bull’s Eye is pressed. When a Job name
has been entered, the Real-time setup menu is displayed (Figure 5-11). See Table 5-2 for a brief
description of the real-time setup components. For a more detailed description of real-time setup,
see “Fieldware - SA Real-Time Setup” on page 3-2.
Figure 5-11: The Real-time Setup Menu
- USER GUIDE 1
- Table of Contents 2
- 3 3
- Fieldware - SA Version 2.00 5
- System Introduction 6
- Legacy 6000 System Features 7
- Activation Description 8
- Legacy 6000 Console 10
- Chapter Notes 12
- Chapter 2 - Getting Started 13
- Software Overview 14
- Standard Pages 16
- Setup Menu Page 18
- Setup Wizard 18
- Setup Sub-Groups 18
- Exiting a Setup Menu Page 18
- Data Entry Page 20
- Pick List Data Entry 20
- Alpha/Numeric Data Entry 20
- Exiting a Data Entry Page 20
- System Setup 22
- Modes of Operation 23
- Rate Control Mode 24
- Console Setup 25
- Setting Description 26
- Lightbar Setup 27
- GPS Receiver Setup 29
- Implement Setup 31
- Entering the Implement Width 33
- Completing Implement Setup 36
- Figure 2-18: Boom Sense Cable 37
- Entering the Section Width 40
- The Offset Distance Y 40
- Controller Setup 43
- Compatible Rate Controllers 44
- Backing up System Files 45
- System Tools 46
- Tool Description 47
- Table 2-10: System Tools 47
- The Device Manager 48
- Button Description 50
- Required Items: 51
- Card Manager 54
- Chapter 3 - Real-time Setup 57
- Real-time Setup Steps 58
- Step Description 59
- Setting up a Job 60
- Creating a New Job 61
- No PCMCIA Card 61
- ARM Launcher 62
- No PCMCIA Card Setup 63
- Setting up a Report 64
- Item Description 65
- Enter the Wind Speed 66
- Enter the Wind Direction 67
- Enter the Temperature 67
- Enter the Relative Humidity 68
- Select the Soil Moisture 69
- Select the Soil Condition 69
- Select the Soil Texture 70
- Select the Soil Tillage 70
- Select the Growth Stage 71
- Running ARM Setup 72
- Table 3-4: ARM Setup Items 73
- Running the ARM Setup Wizard 74
- No PCMCIA Card Selected 75
- Select / Enter a Record File 76
- Select Enter a Guideline File 77
- Enter the System Delay Value 80
- Running Product Setup 81
- Select The Prescription Map 83
- Select the Product Name 85
- Favorites 85
- New Product 85
- Start to type name here 86
- Highlight this window and 86
- Figure 3-36: Selecting a Job 88
- Importing Into a Running Job 89
- Product Application 94
- Real-time Pages 95
- The Rates Page 96
- The Map Page 98
- Soft-key Description 100
- System and Warning Messages 102
- Figure 4-8: Warning Message 103
- Real-time Guidance Operation 104
- Mark Point A 106
- Mark Point B 106
- The Headland Guidance Pattern 107
- Headland Pattern Example 108
- Software Version 2.00 109
- Circle Pivot Example 120
- Marking Point A 120
- Marking Point B 120
- Applied Area Detection 126
- Mapping a Field Boundary 127
- Figure 4-38: Naming the Point 130
- Marking a Hazard 131
- Object Name File 131
- Exiting Real-Time Operation 132
- Lightbar Index 134
- Lightbar State Description 135
- Fieldware-SA Version 2.00 139
- FieldPilot Introduction 140
- Powering Up 145
- Running FieldPilot Setup 146
- Setup Item Description 147
- Real-time Setup 148
- Real-time Operation 149
- Setup Description 150
- The Nudge/Trim Feature 155
- Chapter 6 - Manual Guidance 159
- Manual Guidance Introduction 160
- Chapter 7 - Fieldware - SA 165
- Installation Overview 166
- Figure 7-2: Single Setup Type 168
- Figure 7-3: Repeat Setup Type 168
- Setup Ready to Run 169
- Finishing the Version Update 170
Relacionado con productos y manuales para Ordenadores Teejet Fieldware SA 2.0 for Legacy 6000
Ordenadores Teejet Swath XL Manual de usuario
(162 paginas)
(162 paginas)
(23 paginas)
(23 paginas)
(21 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.091 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales